|
|
Supplies & Equipment for Pottery, Education & Crafts
|
|
|
Fantasy Dragon Project at AMACO.com
Fantasy Dragon
By Natalie Young
Materials
1½" x 7" Friendly Plastic® Metallic Sticks:
- 15 to 20 Shades of Blues and Greens
- 2 Solid White/White
- 1 Solid Red/Red
- 1 Solid Purple/Black
- 3 Solid Dark Pink Pearl/Pink
- Small Round Red Glass Faceted Bead
- Aluminum Foil
- Pinking Shears, Sharp Scissors
- Electric Skillet
- Water
- E-6000 Glue
- Spoon
- Cookie Sheet
- Oven
Step 1
|
Body: Crumple up a 15" piece of foil to create tail, body and neck of dragon. Shape foil into a cylinder tapered at
both ends and bent into “J” for the tail. Add extra foil to fatten the stomach.
|
Step 2
|
Scales: Using pinking shears, cut sticks of Blue and Green Friendly Plastic®. Cut 10 strips to ¼" or ½" x 1½" . Cut
some longer 3¼" strips also. Soften Friendly Plastic® in 140°-150°F water for 5-10 seconds. Wrap one strip of softened
Friendly Plastic® around tip of dragon’s tail. Starting at the bottom, wrap alternating Blue and Green strips
around body, overlapping each strip. Continue until you get to the belly. For the belly, use similarly cut strips of a
complimentary color such as Pinks or Yellows. When the belly and back are covered, outline the belly with one ⅛"
wide strip of Pink. Finish layering strips of Greens and Blues up the back and around the length of the neck. Leave
¼" of foil showing at top of neck.
|
Step 3
|
Arms and Legs: Arms: Cut a 3" strip of Green Friendly Plastic® in half lengthwise. Soften in warm water then
roll it up lengthwise and shape to create a long cylinder that will be the arm from shoulder to the tip of one finger.
Shape to the desired pose. Attach three ½" cylinders to make fingers and thumb. While still soft, shape hand around
bead that will become a “crystal ball”. Attach fingernails (White). Add extra ⅛" wide strips to arm by starting at palm
and wrapping up length of arm in loose coil. This adds color, strength and size to biceps. Repeat for other arm. Legs:
Shape legs from 6" foil, bend to form “L”. Starting at the top, layer strips of Greens and Blues to cover the leg. The
end of the leg piece forms the center toe and two more toes are added on either side. Cut two 1" x 3/16" strips of
Green Friendly Plastic®. Soften, fold in half lengthwise, and roll into ½" cylinder to form toes. Cut ⅛" x 2" strip of
slightly different color with pinking shears and wrap around base of toes to form foot. Cut tiny triangles for toenails
and attach to top of foot with glue. Repeat for other leg. To attach body and legs, soften the body slightly by pouring
hot water from a spoon over area that leg or arm will be attached to. Dip the top end of the arm or leg into hot
water for 20 seconds to properly soften. Push arm or leg and body gently together until they melt together. Hold
for 30 seconds to allow parts to bond together.
|
Step 4
|
Jaws: Cut two 2" equilateral triangles out of Green Friendly Plastic®. Soften them on a cookie sheet in an oven set
at 250°F for five minutes COLOR SIDE DOWN. While triangles are softening, cut small ¼" triangles for teeth out of
White Friendly Plastic®. Remove cookie sheet and quickly place teeth around two sides of each triangle. Let cool. Dip
one triangle into warm water to soften, fold slightly to form lower jaw, and wrap around neck. The second triangle
will form top of head.
|
Step 5
|
Head and Eyes: Dip top of head in water to soften, then shape into inverted “U”. Top teeth should be spread
slightly wider than lower jaw. Cut two ¼" x ¾" strips of White. Soften and roll into small balls for eyes. Wrap 1/16"
strip of Purple around it, make vertical indent with fingernail. Cut two ⅛" wide strips of Turquoise 1½" long. Place
eyes on top and use Turquoise strips across top of eye to hold in place and form eyelids.
|
Step 6
|
Nose: Cut nose piece from Green plastic. Soften and place at front of top jaw, attach it to front fourth of dragon’s
head. Make loop in nose piece and lay the rest up bridge on nose. Very quickly, using butter knife, gently press
onto middle of nose piece. The loop will fold into middle and become nostrils. Ends of nose piece can stick up or be
twisted or cut as horns or ears.
|
Step 7
|
Attach top of head to body: Cut a 3" triangle of Blue plastic. Melt triangle and attach it point up to the
top of the upper head behind horns. While still soft, wrap bottom of triangle around neck behind lower jaw. Cut six
¾" triangles with pinking shears and attach to side of neck as gills.
|
Step 8
|
Spikes: Cut strips of Pink plastic then cut triangles out of one side all the way down. Soften one “spike” right side
down in oven. Remove from oven and put a second one side up on top of it Pink side up so there is color on both
sides. Place back in oven to completely bond. Repeat for each “spike”. Remove from oven and allow to cool. Drip
warm water down back of dragon, soften “spikes” in water and press onto dragon’s back until bonded.
|
Get Acrobat Reader
 |
AMACO Products
|
| |
Contact Us
